Front drive shaft broken

[Clark Kent]

There are ~ 2500 Grenadiers in AU, and so far the reported number (on this forum and social media) that I have seen has been 3. One with lift above 40mm.

My front shaft was recently replaced because CV lube was leaking through a flange bolt hole at the transfer case end. So a shaft fault but not a boot failure. I posted about it here.
Stock suspension.

 

[Tenac]

I need some education here: I'm aligned with all the information on this thread with drive shaft breaking and by lifting putting more stress on that part as well. Would adjustable track bars help avoid the situation of lifting causing a more extreme angle??? I was watching the video below and the gentlemen states that adding the adjustment allows you to get closer to factory with the suspension??? If so this would mean I could life that 1.5" and buy the metalcloak kit to help avoid breaking with a lift.

View: https://youtu.be/ev_JUUC9q-w?t=180

 

[Walter]

I need some education here: I'm aligned with all the information on this thread with drive shaft breaking and by lifting putting more stress on that part as well. Would adjustable track bars help avoid the situation of lifting causing a more extreme angle??? I was watching the video below and the gentlemen states that adding the adjustment allows you to get closer to factory with the suspension??? If so this would mean I could life that 1.5" and buy the metalcloak kit to help avoid breaking with a lift.

View: https://youtu.be/ev_JUUC9q-w?t=180

He had a custom-made double-joint drive shaft installed.

 

[Tenac]

He had a custom-made double-joint drive shaft installed.

Yeah I seen that as well but with the custom drive shaft or shafts with these links we should have zero issues when lifting right? That's my real question here is how to avoid the risk of lifting without going portals which who knows when they will come out. It also seems like these links might help the OEM truck anyway by adding adjustments etc. ?

 

[Dokatd]

You cannot have factory caster and pinion angles with a lift. Certainly not at the same time anyways. To resolve the pinion angle issue you need to adjust the cam bolts on your lower links. When you do this you are also changing your caster. Unfortunately you are changing your caster in the wrong direction for ideal steering characteristics. Additionally you are affecting the oiling of your pinion bearings (though I am not convinced we are even close to this point).

So, the Metalcloak arms are effectively useless as you can't utilize any more adjustment than the factory arms allow for. That is assuming your trucks frame is within the average for frame dimensions. It is possible your frame was pushing the envelope for it's original dimensions and the factory cam bolts don't all enough adjustment, but I'd put money on it that this is not the case with any IG.

The Metalcloak stuff is fine if you want some bling or feel the tubular arms are necessary for strength concerns, but they are not a solution for the front drive shaft issue.

You can absolutely sacrifice your steering a bit for drive shaft angles though. And being completely honest I am currently feeling that this is more viable than we thought. But....I'm not sure it doesn't require the use of the Terraflex joints. I have a suspicion that the Terraflex joints have a different rubber compound for the boot. I'm questioning if the IG boots are failing simply due to a lower quality boot. The way the boot on mine failed made it look like the boot was 20yrs old. It felt dry and hard.

 

[C-Mack]

For sure high CV-joint angles are a contributing factor but so is the constant flexing of the stock boot as the rubber goes from stretched to compressed back to stretched once each rotation which can cause heat fatigue/hardening and tearing of the boot material.

Also, the boot cover acts as a collection point for mud/sand and all sorts of other trail debris which can cause abrasion to the boots while running. In other words, there could be several different variables all contributing at once to the driveshaft failures mentioned around this forum, but one thing is for sure, once the boot is compromised it’s joint is going to fail in short order.

 

[Zimm]

You cannot have factory caster and pinion angles with a lift. Certainly not at the same time anyways. To resolve the pinion angle issue you need to adjust the cam bolts on your lower links. When you do this you are also changing your caster. Unfortunately you are changing your caster in the wrong direction for ideal steering characteristics. Additionally you are affecting the oiling of your pinion bearings (though I am not convinced we are even close to this point).

So, the Metalcloak arms are effectively useless as you can't utilize any more adjustment than the factory arms allow for. That is assuming your trucks frame is within the average for frame dimensions. It is possible your frame was pushing the envelope for it's original dimensions and the factory cam bolts don't all enough adjustment, but I'd put money on it that this is not the case with any IG.

The Metalcloak stuff is fine if you want some bling or feel the tubular arms are necessary for strength concerns, but they are not a solution for the front drive shaft issue.

You can absolutely sacrifice your steering a bit for drive shaft angles though. And being completely honest I am currently feeling that this is more viable than we thought. But....I'm not sure it doesn't require the use of the Terraflex joints. I have a suspicion that the Terraflex joints have a different rubber compound for the boot. I'm questioning if the IG boots are failing simply due to a lower quality boot. The way the boot on mine failed made it look like the boot was 20yrs old. It felt dry and hard.

Heres a thought. It appears if one doesnt want to lift the truck the upper arms will permit dialing in a couple more degrees of camber and put the pinion side boot at about the same angle as if there was a lift, and it wont screw with the steering linkage. It would have been nice if the upper arm length and angle was designed to tilt the pinion upwards a tad under full droop, but it doesn't look that way. Skinny 35's, no lift, and some return to center sounds like a win.

 

[Dokatd]

Heres a thought. It appears if one doesnt want to lift the truck the upper arms will permit dialing in a couple more degrees of camber and put the pinion side boot at about the same angle as if there was a lift, and it wont screw with the steering linkage. It would have been nice if the upper arm length and angle was designed to tilt the pinion upwards a tad under full droop, but it doesn't look that way. Skinny 35's, no lift, and some return to center sounds like a win.

Sure, but why not run more conservative stock settings on the caster and pinion angle and just change the steering stabilizer. I'd much more prefer to swap a passive part like a steering stabilizer than a suspension link that holds the axle in place. You will get all the return to center you could ever want.

Don't get me wrong, I have made many link arms in my life and all were huge improvements, but to be fair that was to add substantial length to the arms by changing the frame side mount.

I'm not afraid to change parts, but someone worried about it should be more comfortable changing the stabilizer than putting in some new link arms. I'm not a Jeep guy so I don't know Metalcloak from Adam so I can't comment on their engineering capabilities, but I think their link kit is a bit of a fallacy.

All just my 2¢

 

[Dokatd]

On another note, I am considering reducing my caster bit by bit until I hit the stock min or find a handling issue.

I originally had my caster set with stock springs. But once the truck was lifted that caster would have changed a fair bit. I suspect I could achieve more favorable driveshaft angles if I dialed it back some. The truck handles very well as is.

 

[Tazzieman]

I'm questioning if the IG boots are failing simply due to a lower quality boot. The way the boot on mine failed made it look like the boot was 20yrs old. It felt dry and hard.

That was my thought from the outset.
It feels more like plastic than rubber, and I guess it is an amalgam of chemicals , some of which are made from Ineos petrochemicals!
I drop under the chassis after every offroad venture to check it.

 

[GN4HIR]

30min call with Tom Woods today. Things are moving along at this point. They have agreed that this is something they want to address for us. I am helping to push it along as best I can with designing and motivation.

Just thought I would ask if there has been any further progress on the Tom Woods driveshaft.

 

[Dokatd]

Just thought I would ask if there has been any further progress on the Tom Woods driveshaft.

No, with the holidays things have been slow. I will hopefully be getting some kind of update shortly after the New Year.