I removed my sill protectors so I could have installed the new rock sliders. The black trim is held on by screws with a T30 head, plus some plastic lugs. The underlying brackets which the trim hangs from are attached using an
I'm at work now so can't check , but you might find this sort of thing useful to haveOverhead console bolts?
Anyone know what the bolts are that are used on the overhead console with the switches? THey seem to be some 4mm hex head with a really coarse thread to them.
Hahaha I was just about to post that myself, having just finished the light shroud install 2 minutes ago.License plate light shroud fasteners are 2x T20 torx.
Longer screws came with the kit from Stu.And if you need longer screws #10 screw at 3/4" long works well. The original screw is metric but the #10 3/4 in black was easy to source in my hardware store.
Great article - I have a Torx T30 corroding (when opening the door you can see it retaining the wing). Thought about replacing it - this thread has stimulated me. Guess it's a Torx T30 - will have to remove and check its length.BACKGROUND
@DaBull and I have been having a discussion of Screw/bolt heads over in the Torque setting thread here. I started a new thread to focus on the various size and types of common screws/bolts used on the Grenadier. The Table will be updated over time.
There will be some variation between cars. I know earlier model Grenadiers had torx bolts along the door sill, my car has hex bolts.#
COMMON HEAD TYPES
A diagram of common heads (it shows no Torx Plus head).
![]()
Source
THE DIFFERENCE BETWEEN TORX AND TORX PLUS
The @DaBull supplied video link of the difference between a Torx head and Torx Plus (Torx+) head.
View: https://youtu.be/U27j1ZvaWeU
THE TABLE
*Commonly loosen/tighten with an Allen key or hex bit. #Commonly loosen/tighten with a socket, spanner or wrench.
Location Head Type Torque Setting Comment Door hinge bolt (exterior) Torx T50 Utility Belt bolts Torx T27 Bracket bolt on grab handle Torx Plus T25P Lower door sill bolts Torx ?? or
Male Hex M10#Roof Rack/Bars Mostly female hex* Various The INEOS Fitting Guides for Accessories often have the various bolt types and torque settings. The head type is commonly a female hex,* on a M6 or M8 bolt. CTECK 120S & 250SE – terminal screws Female hex, use 5mm Allen Key 8 Nm/71 More information in this thread. CTECK 120S & 250SE, base mounting bolts M4 or ST4.2 screws/bolts 2 Nm/18 lb More information in this thread. Oil filter cap 32mm male hex# 25Nm More information in this thread. Oil sump plug ?? 25Nm More information in this thread. Busbar studs Various Various Look here. Headlight surround Torx T27 ?? Plastic trim bolts on both rear doors Torx T27 ?? All my bolts needed some tightening, but I did not overtighten them. However, on the INEOS Picnic Table they used Torx T25 bolt heads, not T27 – go figure! INEOS Picnic Table bolts Torx T25 ?? Torx T27 are used on the plastic trim behind the picnic table. Bolts used on the front raised tie down points near the cargo barrier Torx T40 ?? 2-seater model only. The tie down points on top of the battery box close to the cargo barrier. All 4 of my bolts needed to be tightened (2 each side). Bolts attaching the cargo barrier to the battery box Torx T50 ?? 2-seater model only. The bolts that attach the 2-seater cargo barrier to the battery box. Bolts used to secure L track in cargo area Torx T50 ?? Six bolts are used to secure L Track rails on the cargo area floor. Anchor points in cargo area Torx T45 ?? Not sure where these came from as they were part of the drawer install. Larger anchor bolts used in rear roof No 1 Torx T40 ?? Bolts removed as part of the rear roof shelf install. Look here. Smaller anchor bolts used in rear roof No 2 Torx T25 ?? Bolts removed as part of the rear roof shelf install. Look here. License plate light shroud screws Torx 20 ?? These lights illuminate the rear number plate. Thanks @parb Bolts used in forward roof mounts, under the shrouds Female hex, use 4mm Allen Key* ?? Look here. Bolts along each side of the bonnet/hood adjacent to seals Torx T30 ?? View attachment 7856044 Bolts on the bonnet/hood U bolts Torx T30 ?? View attachment 7856045 Airbox screws PZ3 (Pozidriv 3) ?? Thanks to @Tinki and @Michael H Battery compartment (5 seater) Torx T50 ?? Thanks to @bakepl Under door trim Torx T30 and M10 hex socket ?? View attachment 7859038
Methodology: I take a selection of Torx and Torx Plus bits and work out which fits the best. When there is uncertainty, I look closely at the shape of the screw/bolt head.
I 3D printed my own set. Maybe useful info for those who 3D print.Longer screws came with the kit from Stu.
I added some Marine Goop on the screw threads as I screwed them back in. The screws stay in place, the Goop is easy to remove (if required) and it does not damage the fittings. Now the corrugations cannot loosen the screws.
Fastenal is a good one here in the states. https://fastenal.com/Great article - I have a Torx T30 corroding (when opening the door you can see it retaining the wing). Thought about replacing it - this thread has stimulated me. Guess it's a Torx T30 - will have to remove and check its length.
Used this company in the UK for SS before: https://www.westfieldfasteners.co.uk/Bolts-Screws-Metric/Torx-Cap-Screw-M6x6-T30-A2-Stainless.html