What's new
The Grenadier Forum
Register Now for enhanced site access.
INEOS Agents, Dealers or Commercial vendors please contact admin@theineosforum.com for a commercial account.

Vehicle mounted twin air compressor

Krabby

Krabby

Global Grenadier 76
Forum Moderator
Grenadier Owner
Lifetime Supporter
Local time
11:27 AM
Joined
Nov 5, 2022
Messages
5,054
Reaction score
9,700
Location
New Jersey, USA
MarkusN said:
Hello TheDocAUS:

I used the anchoring of the fastening ring at the rear right (standard). I made a bushing to bridge the recess. This is connected to the rear plate of the air compressor. If the distance is correct, the side bolts/nuts of the compressor can be fastened to the back plate.
I did not want to drill any holes etc. The only thing I had to change was the cable harness feed-through in the lower small cover. I routed the wiring harness to the front of the auxiliary battery.

Regards Markus
Click to expand...
Any pics during install process you can share?
 
Jean Mercier

Jean Mercier

GG#920
Grenadier Owner
Lifetime Supporter
Local time
5:27 PM
Joined
Sep 10, 2022
Messages
2,631
Reaction score
9,397
Location
Sint-Martens-Latem, Belgium
DaBull said:
Hi grenadierboy, That is a very nice clean install. Is that a single cylinder ARB? DaBull
Click to expand...
I would say yes, because I think the "twin cylinder" doesn't fit, unless I am wrong.

I finished my ARB single cylinder compressor installation today (it almost didn't 🌦️ and no work)
I will post some pictures and tips and tricks today or tomorrow, but most inspiration I got on this forum, thanks to everybody who documented their compressor install.
 
Nocrays

Nocrays

Grenadier Owner
Lifetime Supporter
Local time
12:27 AM
Joined
Jul 26, 2022
Messages
352
Reaction score
924
Location
Mandurah, Western Australia
Im keen to flatten out the area over the wheel arch. Im not a fan of drawers so like to have a nice squared off cargo area.

Investigating producing a replacement for the plastic panel out of Aluminium and providing a space on top of the wheel arch for the ARM twin compressor. Then plumb it to a tank under the vehicle near the adblue tanks.

1704855868079.png
 
LeeroyJ

LeeroyJ

Grenadier Owner
Lifetime Supporter
Local time
7:27 PM
Joined
Oct 30, 2023
Messages
167
Reaction score
302
Location
Arizona, USA
stickshifter said:
Third vote for them being hot and loud. I've got the ARB twin mounted in the cubby, just aft of my right rear wheel (Tacoma). I've had one electrical fault, but no mechanical problems with the unit. They are pretty tough, but I'd prefer to have it inside the vehicle. I'm pretty sure it will last longer and be more reliable if its inside the cab some where. No way around the noise and heat though. Its a conundrum...
Click to expand...
A friend of mine and I each bought the twin ARB for our LC200’s in 2012 at the same time. He had a VXR with electric seats (so not enough room to mount it under the driver’s seat), so he ordered the Slee mounting kit and mounted it in the engine bay. I had a GXR with manual seats so mounted mine under my seat. In November 2023 when I sold my 200, my twin compressor was still as good as new. He was on his third. They had about the same use (we camped in the Saudi desert together and each had 35”s). There were two differences: the first, the heat between the air conditioned air mine received and the engine bay air his received. Second, and probably more important, if I accidentally hit the switch with my knee, I could immediately tell it had done it. If he did, he may not know for days (since after filling the tank, it only came on when pressure dropped). Take that anecdotal evidence for what it’s worth when considering mounting locations (nothing?).
 
Krabby

Krabby

Global Grenadier 76
Forum Moderator
Grenadier Owner
Lifetime Supporter
Local time
11:27 AM
Joined
Nov 5, 2022
Messages
5,054
Reaction score
9,700
Location
New Jersey, USA
Nocrays said:
Im keen to flatten out the area over the wheel arch. Im not a fan of drawers so like to have a nice squared off cargo area.

Investigating producing a replacement for the plastic panel out of Aluminium and providing a space on top of the wheel arch for the ARM twin compressor. Then plumb it to a tank under the vehicle near the adblue tanks.

View attachment 7839184
Click to expand...
I agree totally - it's such an odd thing that IA didn't do something here to be more practical.
 
ADVAW8S

ADVAW8S

Global Grenadier 0044
Lifetime Supporter
Founding Guard
Local time
8:27 AM
Joined
Oct 11, 2021
Messages
1,974
Reaction score
2,878
Location
Kirkland, WA, USA
Krabby said:
I agree totally - it's such an odd thing that IA didn't do something here to be more practical.
Click to expand...
Um, I think IA was forward thinking, they slapped a laptop sticker on it. This was built on purpose as a laptop work station. Now you can squeeze yourself back there to knock out that email
 
Last edited:
Krabby

Krabby

Global Grenadier 76
Forum Moderator
Grenadier Owner
Lifetime Supporter
Local time
11:27 AM
Joined
Nov 5, 2022
Messages
5,054
Reaction score
9,700
Location
New Jersey, USA
ADVAW8S said:
Um, I think IA was forward thinking, they slapped a laptop sticker on it. This was built on purpose as a laptop work station. Now you can squeeze yourself back there to knock out that email
Click to expand...
Or maybe a live broadcast for a podcast.

Right @Stu_Barnes ;)
 
Jean Mercier

Jean Mercier

GG#920
Grenadier Owner
Lifetime Supporter
Local time
5:27 PM
Joined
Sep 10, 2022
Messages
2,631
Reaction score
9,397
Location
Sint-Martens-Latem, Belgium
marcusnilsson said:
I saw that also. What do you guys think about the placement of the compressor? I’m not sure. Looks a bit forced.
Click to expand...
I don't like it either, it takes too much space in the boot. It is of course a quite easy install, compared to the "one cylinder ARB" install behind the secondary battery (space is very tight).
 
stickshifter

stickshifter

Local time
4:27 PM
Joined
Nov 14, 2021
Messages
1,172
Reaction score
2,423
marcusnilsson said:
I saw that also. What do you guys think about the placement of the compressor? I’m not sure. Looks a bit forced.
Click to expand...

Yeah - not ideal.

I know most people will be keeping the second row of seats, but some of us are planning on doing the rear seat delete from Goose Gear. I'm thinking there will be somewhere in this set-up to mount a compressor. It looks like there is a big overhang - i.e. the flat floor extends over the box that contains the batteries and other electronics. It looks like it might be possible to mount a twin ARB somewhere around where I put the red circle.

If @GooseGear has any thoughts - be great to hear them.

P.S. I'm not interested in the single motor compressor mounted inside the electronics box, for two reasons: the single is a little slow for four tires (particularly if the tires are 'oversized'), and I think it might generate too much heat in there.

GG_rear_seat_5.jpg

Photo from Goose Gear: https://www.goose-gear.com/products/ineos-grenadier-2024-present-second-row-seat-delete-plate-system
 
Last edited:
S

Strib81

Grenadier Owner
Local time
9:27 AM
Joined
May 23, 2023
Messages
37
Reaction score
136
Location
USA
ARB Twin Compressor installed behind trim!!
Had to relocate ac inverter and build wiring harness extentions as well as custom mounts for everything.
 

Attachments

  • IMG_3259.jpeg
    IMG_3259.jpeg
    3.5 MB · Views: 186
  • IMG_3255.jpeg
    IMG_3255.jpeg
    2.3 MB · Views: 197
  • IMG_3190.jpeg
    IMG_3190.jpeg
    1.5 MB · Views: 192
Krabby

Krabby

Global Grenadier 76
Forum Moderator
Grenadier Owner
Lifetime Supporter
Local time
11:27 AM
Joined
Nov 5, 2022
Messages
5,054
Reaction score
9,700
Location
New Jersey, USA
Is there enough air circulating to cool the compressor?
 
Tazzieman

Tazzieman

Grenadier Owner
Lifetime Supporter
Founding Guard
Local time
3:27 AM
Joined
Sep 30, 2021
Messages
6,697
Reaction score
13,292
Location
Tasmania
Krabby said:
Is there enough air circulating to cool the compressor?
Click to expand...
There's only one way to find out!
Anyway , once you start removing panels it's popped the cherry of boring holes in things :D Don't worry about the "next owner".
 
S

Strib81

Grenadier Owner
Local time
9:27 AM
Joined
May 23, 2023
Messages
37
Reaction score
136
Location
USA
Krabby said:
Is there enough air circulating to
Click to expand...

Krabby said:
Is there enough air circulating to cool the compressor?
Click to expand...
The twin compressor has a cooling fan to circulate air. Notice the vents on the trim panel. They are directly above the compressor air intakes. So I believe the answer is yes.
 
You must log in or register to reply here.

Similar threads

N
Using the NATO socket to power equipment - This is how it works.
2
Replies
25
Views
2K
Phred
Phred
parb
Tjm compressor and bracket for engine bay
Replies
2
Views
335
OzyGrenie
OzyGrenie
Tom D
Who wants an under seat bracket for ARB twin compressor and 4 l air tank?
Replies
3
Views
386
IslandFalconer
I
Bodhi’s Grenadier
CATuned Offroad X TJM on board air kit
Replies
6
Views
1K
Bodhi’s Grenadier
Bodhi’s Grenadier
TheDocAUS
AUSTRALIA: Third party suppliers for the Grenadier
15 16 17
Replies
322
Views
22K
Grenadian
Grenadian
Forum Store
The officially unofficial podcast for INEOS Automotive Grenadier Works Podcast
INEOS Grenadier Configurator

Latest posts

Share this page

Back
Top Bottom