Show us your mods.

Cheshire cat · Nov 1, 2023

Any idea on what the print cost might be for an item like this?

ADVAW8S · Nov 1, 2023

DaveB said:
Do people get attacked by butterflies a lot?

View: https://youtube.com/shorts/A7I7L8lxbqU?si=S_eOc9_1g2-T1UaE

Cheshire cat · Nov 1, 2023

I think the knife is a Leatherman but don't let that fact disrupt the thread.

IG_in_AZ · Nov 2, 2023

Cheshire cat said:
Any idea on what the print cost might be for an item like this?

Or what material might be best? I watched a video explaining all the different types of filaments and I must admit, I'm feeling a bit overwhelmed and had no idea there were so many different kinds.

chrsbe · Nov 2, 2023

ADVAW8S said:
Please tell me you carry a butterfly knife in your car. There is only one other person I known that carries a butterfly knife and that is my uncle.

Nope. Sorry it is an old Leatherman i have there. But if you wish you probably could. I have designed the deeper compartments so it does fit several sizes of folding knives....

chrsbe · Nov 2, 2023

I printed it on a consumer grade fdm printer with pla material. I think pet or abs would also work fine.

David van Breda · Nov 2, 2023

explorersoverland said:
Added two sideboards from HGM-Rack last week for the Overland Fuel diesel tanks and on the other side the ladder for the RTT.

The sideboards are light and because it consists of one part, it is easy to install.

Mounted the ladder with clamps from Quick fist. They are very solid and recommended for installing items on your grenadier that come off more often.

Lovely setup you have here!
I'm a huge fan of the Bush Company products.
I am however curious about the Grenadier's performance and general feel with all this added weight and height.
Is the standard suspension coping with it?

Max · Nov 2, 2023

I had an idea to make a temporary off and on canopy that shades and rainproofs the rear entrance with the doors open and the table down for a bite to eat and a cuppa...I sourced some double clips[Saint S350] that went straight over the 25mm grab/tie down rail and I thought of using 25mm tubes for the canopy to thread onto...the tube was going to be too long...I sourced a spreader rail[Tentworld] that is telescopic and cut them down to fit across behind the back seat[pic]...the spreader rails have an eyelet on each end...one for a pole if needed in the breeze and the other a tie down...the rails will sit on the rubber surrounds of the grab/tie down rail area and tension from the tonneau cover material will hold the rails in place...yet to be made...but the interesting part is that I have wanted bars to go into the luggage barrier fixing points[pic]for grab rails for entry[pic]to the back seats or as in the rear to hang things off...or whatever...perfect dual system...I will post the final canopy idea...the spreader rail is OZ made and strong as[pic]...my wife has just tested the hand rail to enter the vehicle and I got the all clear...that is my arm thank you...happy times

chrsbe · Nov 2, 2023

I would try to pay no more than 30 to 40 bucks.

Cheshire cat said:
Any idea on what the print cost might be for an item like this?

Rok_Dr · Nov 2, 2023

@chrsbe thanks so much for sharing, appreciated!

cheers
Steve

Tom D · Nov 3, 2023

A couple of pics of the buzz step sliders.

Krabby · Nov 3, 2023

Those are high lift holes (if you have the little adapter), correct?

Tom D · Nov 3, 2023

Yes I think so.

Krabby · Nov 3, 2023

Tom D said:
Yes I think so.

I hope so - I had that setup on my series II and kept the adapter when I sold the truck.

Cheshire cat · Nov 3, 2023

Krabby said:
I hope so - I had that setup on my series II and kept the adapter when I sold the truck.

What adaptor are you referring to? I have the same steps

Krabby · Nov 3, 2023

Cheshire cat said:
What adaptor are you referring to? I have the same steps

LINK

I'm pretty sure I got mine from Rovers North, but I have to imagine other people make/sell them.

Claude · Nov 3, 2023

chrsbe said:
Here is the 3d file for the insert of the cubby box of the Ineos Grenadier.
You can 3d print it. If you do not own a 3d printer use a print service like materialize or something similar and maybe also cheaper.
free to use for everyone. you can alter the file as much as you like. please do not sell it. if someone asks where you got it from please refer to this forum.
enjoy
ps.: would be nice if you post a photo of your prints.

View attachment 7831457 View attachment 7831448

thank's for the design; I've just oredered one myself from a printshop

Clark Kent · Nov 5, 2023

chrsbe said:
Here is the 3d file for the insert of the cubby box of the Ineos Grenadier.
You can 3d print it. If you do not own a 3d printer use a print service like materialize or something similar and maybe also cheaper.
free to use for everyone. you can alter the file as much as you like. please do not sell it. if someone asks where you got it from please refer to this forum.
enjoy
ps.: would be nice if you post a photo of your prints.

View attachment 7831457 View attachment 7831448

Thank you for your development on this insert and for sharing the 3D file.
You clearly have the ability and the means for this work. Are you interested in developing other solutions?
The flat shelf on top of the dashboard is begging to be improved. Ineos put some thought into this area with the non-slip pad, but the edge is not high enough to keep things in place when driving. A tray of approximately 25mm (1 inch) deep would be a good improvement. Is that something you might use yourself, and be interested in developing and sharing the file?
Maybe we could crowd source designs for this and other areas then commission you to develop a solution. You should not do it for free though!

AnD3rew · Nov 5, 2023

Clark Kent said:
Thank you for your development on this insert and for sharing the 3D file.
You clearly have the ability and the means for this work. Are you interested in developing other solutions?
The flat shelf on top of the dashboard is begging to be improved. Ineos put some thought into this area with the non-slip pad, but the edge is not high enough to keep things in place when driving. A tray of approximately 25mm (1 inch) deep would be a good improvement. Is that something you might use yourself, and be interested in developing and sharing the file?
Maybe we could crowd source designs for this and other areas then commission you to develop a solution. You should not do it for free though!

I have this, simple and really useful

View: https://youtu.be/0kqJ1pl5SZY?feature=shared

Clark Kent · Nov 5, 2023

AnD3rew said:
I have this, simple and really useful

View: https://youtu.be/0kqJ1pl5SZY?feature=shared

I have seen that organiser and their underseat bags, etc. Looks like a quality item. It's not a A$196 problem for me at this point.

Search

Search

Show us your mods.

Cheshire cat

ADVAW8S

Global Grenadier 0044

Cheshire cat

IG_in_AZ

Global Grenadiers #1372

chrsbe

chrsbe

David van Breda

Max

Attachments

chrsbe

Rok_Dr

Tom D

Krabby

Global Grenadier 76

Tom D

Krabby

Global Grenadier 76

Cheshire cat

Krabby

Global Grenadier 76

Claude

Clark Kent

Attachments

AnD3rew

Inch deep and a mile wide.

Clark Kent

Similar threads

Latest posts

Share this page