Show us your mods.

[Deichrutscher]

You can try to print with a gcode file from Prusa Slicer.
You have to configure "Organic Support" (Print Settings/Support material/Style)
Calculated Print Time round about 1Day 7Hours

Prusa Slicer can work with other Printers, see below.

 

[FlyersFan76]

You can try to print with a gcode file from Prusa Slicer.
You have to configure "Organic Support" (Print Settings/Support material/Style)
Calculated Print Time round about 1Day 7Hours

Prusa Slicer can work with other Printers, see below.

View attachment 7852513View attachment 7852514View attachment 7852515

Thank you

I was thinking of trying that slicer also.

 

[FlyersFan76]

Installed an aluminum storage bin over the wheel well. Picked it up on Amazon but available on eBay as well. It was pricey at $300 shipped but I’m very pleased with the quality and fit. Less stuff flying around the rear now… can still lash things down using the MOLLE panel design, it would seem.

Came fully assembled. 5 minute install - you simply replace the tie downs with supplied hardware. Done.

My bison gear shelf that mounts to the roof arrives Friday…….

I have been eyeing this up. I am surprised no one else has made one yet. Not that I have seen yet anyway.

 

[MShepherd]

I raised the driver and passenger seats.

I'm 180 (5.9), my driver's seat was pumped up quite high to sit comfortably. So I built a spacer out of WPC (wood plastic composite) that gives me more storage space of 2 cm in height under the seats.

Don't try this at home, I have no idea if it's legal or safe!

And I think my self-made holder for the fire extinguisher is closer to the seat frame than the original (more legroom).

 

[Tom D]

Indeflates are out of stock in the UK, so I made my own. Worked out a lot cheaper too.

 

[Krabby]

Indeflates are out of stock in the UK, so I made my own. Worked out a lot cheaper too. View attachment 7857044

Sounds like a good “how to” post is coming our way!

 

[Max]

Indeflates are out of stock in the UK, so I made my own. Worked out a lot cheaper too. View attachment 7857044

You're pretty handy by the look of that and you even managed to fit a Makita battery into a Stihl chainsaw

 

[Tom D]

You're pretty handy by the look of that and you even managed to fit a Makita battery into a Stihl chainsaw

Its a Dolmar, (owned by Makita) the scabbard is Stihl... Well spotted! Handy little saw actually.

 

[Karearea]

I think it's the same as my 18v Makita model just from the looks (different colour obviously) and the oil filler location. I too am super happy with my saw

 

[Khalfan323]

5 more HP

 

[Pat-Ard]

Finally I found an adequate "Protector" for the tow ball.

 

[Eric]

Finally I found an adequate "Protector" for the tow ball.
View attachment 7858011
View attachment 7858012View attachment 7858013

I don't know about Germany but if you parked that in most places in the UK, it would be nicked quite quickly.

 

[Pat-Ard]

I don't know about Germany but if you parked that in most places in the UK, it would be nicked quite quickly.

I fear this will happen!!!

 

[Clark Kent]

Finally I found an adequate "Protector" for the tow ball.
View attachment 7858011
View attachment 7858012View attachment 7858013

Perspective..
I contend that you have found an appropriate use for that awkward looking Euro hitch

 

[[ Adam ]]

 

[Rok_Dr]

View attachment 7858096

I like that! Did you make or buy it?

 

[[ Adam ]]

I like that! Did you make or buy it?

It's from front runner (for their rack) plus one of these

 

[Max]

I have been toying with the Grill for some time and finally, I have wrapped the above and below white sections to extend the height of the grill to give it more of the old Defender look...the chrome strips will stay there for the moment, they still look ok because they line up with the headlight surrounds, top and bottom...I think it toughens up the front end but so many variations could be had...if it were a darker colour and I had the gloss black roof, I would look at a gloss black grill and headlight surrounds...for that matter, it probably would work here...back to the photoshop

 

[Pat-Ard]

I know, it‘s not the original font of the Quatermaster, but it fits nicely… A friend was so kind to let it plot for me.

But hey, I don‘t really care.
Carefully place the sticker on the side and took measures.

After removing the base foil it looked like this.

And the final result…

I hope you like it…

 

[Krabby]

Well done. Looks pretty good.

FWIW, the actual font can be found HERE!