What's new
The Grenadier Forum
Register Now for enhanced site access.
INEOS Agents, Dealers or Commercial vendors please contact admin@theineosforum.com for a commercial account.

Underbody Protection from Rival

74CampySuperRecord

74CampySuperRecord

Grenadier Owner
Lifetime Supporter
Local time
4:23 PM
Joined
Nov 15, 2023
Messages
177
Reaction score
248
Location
Arizona
I will be doing the mod tomorrow.
 

Attachments

  • IMG_4781.jpeg
    IMG_4781.jpeg
    1.6 MB · Views: 110
parb

parb

Grenadier Owner
Lifetime Supporter
Local time
3:23 PM
Joined
Sep 10, 2023
Messages
936
Reaction score
1,337
Location
Silicon Valley, CA, USA
I'm going to do it next weekend.
Just ordered a jig saw blade and cutting fluid from Amazon:
Bosch T127D Special for Aluminum
A9 aluminium cutting fluid
 
74CampySuperRecord

74CampySuperRecord

Grenadier Owner
Lifetime Supporter
Local time
4:23 PM
Joined
Nov 15, 2023
Messages
177
Reaction score
248
Location
Arizona
I went ahead and did the mod today. It took about an hour and a half to do the whole job.
 

Attachments

  • IMG_4788.jpeg
    IMG_4788.jpeg
    2.2 MB · Views: 56
  • IMG_4790.jpeg
    IMG_4790.jpeg
    2.9 MB · Views: 57
  • IMG_4794.jpeg
    IMG_4794.jpeg
    1.6 MB · Views: 77
Nadir5

Nadir5

Grenadier Owner
Local time
3:23 PM
Joined
Jan 25, 2024
Messages
54
Reaction score
52
Location
Los Angeles, CA, USA
Did the square notch yesterday (using a Jigsaw and an aluminum-specific blade with aluminum-specific cutting oil - hat tip to @parb for the model numbers). It didn't take long at all. Used blue tape as a cutting guide and had the plate clamped to a sawhorse for stability. Getting it installed was a bit of a chore because the crossmember and my chassis weren't exactly the right dimensions (I had to use 2 washers instead of one of the included spacers, and even then needed a bit of hammering). Once in place it was a breeze to get some LocTite on the bolts and tighten everything up. I did notice the relative tightness of the work area under the truck compared to my lifted '94 Defender-90 on 33s. :) Taller tires are definitely on the want-list.
 
ColoradoMike

ColoradoMike

Grenadier Owner
Local time
4:23 PM
Joined
Sep 3, 2024
Messages
89
Reaction score
172
Location
Colorado, USA
Since we just picked up our Grenadier....have the "cutting issues" been resolved with the underbody protection? Very interested but would like to NOT have to do some cutting on the skid plates.
 
parb

parb

Grenadier Owner
Lifetime Supporter
Local time
3:23 PM
Joined
Sep 10, 2023
Messages
936
Reaction score
1,337
Location
Silicon Valley, CA, USA
Rival is having a new version of the skid plate coming out in mid-november. They have stopped selling the current version until then. anything you order from rival today will be the new design. If you got the old design you can either notch the plate in the location where its too tight or they will send you the updated version once it ships.
 
ColoradoMike

ColoradoMike

Grenadier Owner
Local time
4:23 PM
Joined
Sep 3, 2024
Messages
89
Reaction score
172
Location
Colorado, USA
parb said:
Rival is having a new version of the skid plate coming out in mid-november. They have stopped selling the current version until then. anything you order from rival today will be the new design. If you got the old design you can either notch the plate in the location where its too tight or they will send you the updated version once it ships.
Click to expand...
Thanks for the update! Something on my list!
 
O

Ovrland Bill

Grenadier Owner
Lifetime Supporter
Founding Guard
Local time
3:23 PM
Joined
Sep 25, 2021
Messages
317
Reaction score
342
ColoradoMike said:
Very interested but would like to NOT have to do some cutting on the skid plates.
Click to expand...

My Rival skid plate showed a ‘contact mark’ from the front differential just from street driving. As I DO plan on off-roading before November, I went ahead and had the front corner ‘notch’ cut.
 
O

ORSO

Grenadier Owner
Local time
12:23 AM
Joined
Apr 2, 2023
Messages
266
Reaction score
348
Location
Italy
Has anyone fitted the Rival radius arm skid plates? I can't find detailed photos of the product online.

I am looking for 4 protections for the 4 radius arms. Almont only makes the left rear one and SPP only has the rear ones.

can you post some pictures? do you have any alternatives to rival?

thanks
 

Attachments

  • Screenshot 2024-09-30 alle 10.59.11.png
    Screenshot 2024-09-30 alle 10.59.11.png
    2.4 MB · Views: 40
Logsplitter

Logsplitter

Photo Contest Winner
Grenadier Owner
Lifetime Supporter
Local time
11:23 PM
Joined
Oct 31, 2022
Messages
2,813
Reaction score
10,064
Location
🇬🇧
ORSO said:
Has anyone fitted the Rival radius arm skid plates? I can't find detailed photos of the product online.

I am looking for 4 protections for the 4 radius arms. Almont only makes the left rear one and SPP only has the rear ones.

can you post some pictures? do you have any alternatives to rival?

thanks
Click to expand...
I’ve fitted the Almont rear left plate but isn’t the rear right covered by something possibly the fuel tank guard anyway. I’m not with my vehicle do can’t check that.
Edit that. I think the fuel tank guard sticks slightly lower that the right side arm so fairly well protected anyway
IMG_3965.jpeg
 
ECrider

ECrider

Grenadier Owner
Lifetime Supporter
Local time
11:23 PM
Joined
May 4, 2022
Messages
3,349
Reaction score
5,589
Location
UK
Logsplitter said:
I’ve fitted the Almont rear left plate but isn’t the rear right covered by something possibly the fuel tank guard anyway. I’m not with my vehicle do can’t check that.
Edit that. I think the fuel tank guard sticks slightly lower that the right side arm so fairly well protected anyway View attachment 7871645
Click to expand...
yes the fuel tank guards will cover the offside rear arm. still trying to get around to fitting this last piece from Almont
 
O

Ovrland Bill

Grenadier Owner
Lifetime Supporter
Founding Guard
Local time
3:23 PM
Joined
Sep 25, 2021
Messages
317
Reaction score
342
Transfer Case skid plate from Rival fitted without difficulty. Although it looks low, actual ground clearance is a bit over 11”, which is still more than the OEM Fuel Tank skid plate.
 

Attachments

  • IMG_9720.jpeg
    IMG_9720.jpeg
    2.1 MB · Views: 46
  • IMG_9719.jpeg
    IMG_9719.jpeg
    2.3 MB · Views: 50
  • IMG_9717.jpeg
    IMG_9717.jpeg
    2.7 MB · Views: 46
74CampySuperRecord

74CampySuperRecord

Grenadier Owner
Lifetime Supporter
Local time
4:23 PM
Joined
Nov 15, 2023
Messages
177
Reaction score
248
Location
Arizona
Ovrland Bill said:
Transfer Case skid plate from Rival fitted without difficulty. Although it looks low, actual ground clearance is a bit over 11”, which is still more than the OEM Fuel Tank skid plate.
Click to expand...
Mine arrived last week. I am debating on whether or not to install it before Moab.
 
parb

parb

Grenadier Owner
Lifetime Supporter
Local time
3:23 PM
Joined
Sep 10, 2023
Messages
936
Reaction score
1,337
Location
Silicon Valley, CA, USA
I got mine on Friday. But I left for Moab Friday morning. I'm somewhere around winnemucca in Nevada.
Planning to roll into Utah tonight.
 
O

Ovrland Bill

Grenadier Owner
Lifetime Supporter
Founding Guard
Local time
3:23 PM
Joined
Sep 25, 2021
Messages
317
Reaction score
342
74CampySuperRecord said:
Mine arrived last week. I am debating on whether or not to install it before Moab.
Click to expand...
Are you perhaps waiting to see if this skid plate actually protects (or causes ‘hang-ups’) on our trails in Moab?
 
74CampySuperRecord

74CampySuperRecord

Grenadier Owner
Lifetime Supporter
Local time
4:23 PM
Joined
Nov 15, 2023
Messages
177
Reaction score
248
Location
Arizona
Ovrland Bill said:
Are you perhaps waiting to see if this skid plate actually protects (or causes ‘hang-ups’) on our trails in Moab?
Click to expand...
More like I am feeling lazy and I don’t want to run into the problems with the insert nuts that some members here have had while installing. I already chased the threads to prevent cross threading.

I need to get the front suspension spring problem on my wagon remedied first.

I cannot wait to meet up with everyone.
 
O

Ovrland Bill

Grenadier Owner
Lifetime Supporter
Founding Guard
Local time
3:23 PM
Joined
Sep 25, 2021
Messages
317
Reaction score
342
74CampySuperRecord said:
More like I am feeling lazy and I don’t want to run into the problems with the insert nuts that some members here have had while installing. I already chased the threads to prevent cross threading.

I need to get the front suspension spring problem on my wagon remedied first.

I cannot wait to meet up with everyone.
Click to expand...
“Priorities”, I get it!
 
Nadir5

Nadir5

Grenadier Owner
Local time
3:23 PM
Joined
Jan 25, 2024
Messages
54
Reaction score
52
Location
Los Angeles, CA, USA
Installed mine this morning. The insert nuts are fiddly for sure, and the one that goes into the chassis is a little scary since if you lose the holding tabs, you're SOL. Got them all in, though, so no worries. For the two that go into the cross member, I used an Allen wrench through a nearby hole to put some downward pressure on it to make starting the bolt easier (after already running the bolts all the way through the inserts beforehand).
 
You must log in or register to reply here.

Similar threads

angstorms
Looks like we have choices in US for Diff Skid Plates
2 3
Replies
48
Views
3K
Dual Grenny Guy
Dual Grenny Guy
G
Dinitrol underbody protection. Anyone used this?
Replies
18
Views
2K
Skiprat
S
bbq4133
Build Thread Sir Grenulph Fiennes - '24 Scottish White Trialmaster
Replies
12
Views
858
bbq4133
bbq4133
bbq4133
First Big Off Road Trip Completed - Thoughts on the Grenadier
Replies
18
Views
2K
emax
emax
ethree
2k mile review.
Replies
6
Views
719
LC0013
LC0013
Forum Store
The officially unofficial podcast for INEOS Automotive Grenadier Works Podcast
INEOS Grenadier Configurator

Latest posts

Share this page

Back
Top Bottom