Custom Camper Works

das mo · Jun 10, 2023

Moving on to the gutter mount prototyping.
For those who wondered, the gutters have a 10 degree tilt.

das mo · Jun 10, 2023

Ok.
First proto done.
Need to get a bit deeper with the notch.
Enough space with this setup to actually go for the 50mm shorter DOT150 mounts @Pat-Ard.
Need to allow water drainage.
Good progress for just spending few hours on it.

Pat-Ard · Jun 10, 2023

Nice progress… But do you really trust on wood?

das mo · Jun 10, 2023

The idea is to have it 3D printed.

Pat-Ard · Jun 10, 2023

Ahhhhh… Fuchs.

das mo · Jun 10, 2023

Pat-Ard said:
Ahhhhh… Fuchs.

Na sijja.

But I assume hard wood would work too for one trip, if sealed.

MilesD · Jun 10, 2023

MrMike said:
These are breeding grounds for bacteria, shower in water from one...maybe, but after making my own many years ago and adding potentially 40kg on the roof I've gone for a more civilised form of hot water, on demand and able to adjust temperature.

Joolca, cannot fault it as a portable heater, and will hang off the utility rail….once the van arrives

das mo · Jun 10, 2023

Super nice fit.
Will try to mount tomorrow morning and then work on tue front ones that need to be shaped slightly different due to the embossment of the roof just behind the safari windows.

das mo · Jun 11, 2023

Prototype of the foot spreading the weight full depth of the gutter over 20cm width is a nice fit.

Also started working on the most tailored drawer there is. Using the left bottom space with the jack access in the front and a corner cut in the back for cool air flow towards the fridge from behind the rack.

das mo · Jun 19, 2023

Busy days.

Boot rack is finished and installed.
Few little enhancements to do around securing boxes from moving.

Changed process to the oak pieces, that will function as proto during the first trip before going 3D plastic print or allow milling after.

I also milled spacers to distribute some weight onto the rails, if needed.
They do not meet the allow profile above perfectly, but it is what it is with the trip approaching fast.

DCPU · Jun 19, 2023

das mo said:
View attachment 7817134

I also milled spacers to distribute some weight onto the rails, if needed.
They do not meet the allow profile above perfectly, but it is what it is with the trip approaching fast.

Have you discounted drilling through the 80/20 and mounting them directly to the mounting points for the tie down rail?

das mo · Jun 19, 2023

DCPU said:
Have you discounted drilling through the 80/20 and mounting them directly to the mounting points for the tie down rail?

Not at the moment as I still hope my other 6 feet will carry the weight and therefore can consider these optional. Let's see. Hope too have all parts done soon, so that I can finally load things onto the car and understand physics...

das mo · Jun 21, 2023

Final design done.

6 pieces will need some individual fitting tomorrow before getting some spar varnish.
Planning to bring all the pieces together this weekend for the first time.

das mo · Jun 25, 2023

It is on.

YIPPE · Jun 25, 2023

Great prototype/concept. Looks to have no deflection in the gutter. Great work

das mo · Jun 25, 2023

YIPPE said:
Great prototype/concept. Looks to have no deflection in the gutter. Great work

Some.
I made 4 different types.
After tightening it all up, there is a slight wave in tue gutter, but much better than tue ones I have seen caused by “professional” makers.
Time will tell, if this works.
I made 4 additional allow legs that I can add any time for extra strength.

DaveB · Jun 25, 2023

das mo said:
Some.
I made 4 different types.
After tightening it all up, there is a slight wave in tue gutter, but much better than tue ones I have seen caused by “professional” makers.
Time will tell, if this works.
I made 4 additional allow legs that I can add any time for extra strength.

View attachment 7817962

Looks interesting but how does a home made system pass roadworthy laws or insurance?

32 ways to make your 4WD illegal (and void your insurance)

There are a lot of ways to make your 4WD illegal, and the risk is significant. Find out whether your 4WD complies here, and what to look for.

www.4wdingaustralia.com

Krabby · Jun 25, 2023

I may have missed this along the way, in case anyone else missed it, here’s a link to the manufacturer.
DAYSONTRACKS

das mo · Jun 25, 2023

DaveB said:
Looks interesting but how does a home made system pass roadworthy laws or insurance?

32 ways to make your 4WD illegal (and void your insurance)

There are a lot of ways to make your 4WD illegal, and the risk is significant. Find out whether your 4WD complies here, and what to look for.

www.4wdingaustralia.com

View attachment 7817964

Everything we put onto our roof here is considered cargo. The driver is responsible for securing it.

das mo · Jun 25, 2023

I actually trust mine more than most of the ones I have seen out there.
Not sure how things are handled downunder, but if you lose cargo, break something, … with a rack you bought from the market, the maker will blame things on you anyways, so it does not make a difference after all.
Take a 50kg rack. Go offroad, which cuts the 150kg into half for most makers. As soon as you pack more than 25kg on top, no insurance or warranty will do you any good.

Search

Search

Custom Camper Works

das mo

das mo

Pat-Ard

Global Grenadier #00520

das mo

Pat-Ard

Global Grenadier #00520

das mo

MilesD

das mo

das mo

das mo

DCPU

das mo

das mo

das mo

YIPPE

GG #00286

das mo

DaveB

32 ways to make your 4WD illegal (and void your insurance)

Krabby

Global Grenadier 76

das mo

32 ways to make your 4WD illegal (and void your insurance)

das mo

Similar threads

Latest posts

Share this page