Bull bar

globalgregors · Mar 14, 2023

TheDocAUS said:
No, I looked yesterday for that exact thing. But you could mount one using a bracket.

I purchased a couple of tabs to weld on, although they might be short on clearance.

TheDocAUS · Mar 14, 2023

That would work, as long as it was welded to the backside of the roo bar. You cannot, in NSW, have sharp edges on the front side of the bar, so it would be illegal to weld it to the front side. Long winded version here. Practical guide here.

Andrew Kilby · Mar 14, 2023

There is not a lot of room between the top rail and the vehicle. My fishing rod holder certainly won't fit. I am sure there is a plan B but I haven't figured out out yet.

DaveB · Mar 14, 2023

Andrew Kilby said:
There is not a lot of room between the top rail and the vehicle. My fishing rod holder certainly won't fit. I am sure there is a plan B but I haven't figured out out yet.

I assume you are referring to these types of rod holders.
On vehicles everywhere in Australia but very much illegal.
Nothing is allowed to protrude above the bonnet line and nothing is allowed in the drivers line of sight.
Not to mention pedestrian safety rules
I guess you would have to be doing other things wrong for a cop to book you on it, or be involved in an accident.
I saw a guy get booked for driving lights on top of the bull bar (not the actual vehicle) and for his antennae's on the bar but he was driving like a dick on the Gold Coast

Andrew Kilby · Mar 14, 2023

This is the type of rod holder I use. I find they are easy to fit and don't obstruct the road view any more than ladder racks. I don't know for sure but i believe that because of the height they are treated as long load and therefore allowed a small forward protrusion. But I wouldn't bet my house on it.

DaveB · Mar 14, 2023

Andrew Kilby said:
View attachment 7806118

This is the type of rod holder I use. I find they are easy to fit and don't obstruct the road view any more than ladder racks. I don't know for sure but i believe that because of the height they are treated as long load and therefore allowed a small forward protrusion. But I wouldn't bet my house on it.

You have to remove them when not holding rods, which looks like that one does easily.
Blocking drivers view is a simply a clear view to the ground 11 Metres in front of the vehicle for the driver
I think a cop would be hard to find fault with that one.

bigleonski · Mar 15, 2023

DaveB said:
You have to remove them when not holding rods, which looks like that one does easily.
Blocking drivers view is a simply a clear view to the ground 11 Metres in front of the vehicle for the driver
I think a cop would be hard to find fault with that one.

Yes- not illegal when in use.

TheDocAUS · Mar 19, 2023

Looking further at pictures and videos I am confident the brackets and foldable aerial mounts can be fitted to the Roo Bar, they just need to be placed on the outer side of the roo bar supports (either left or right side).

Tazzieman · Mar 19, 2023

TheDocAUS said:
Looking further at pictures and videos I am confident the brackets and foldable aerial mounts can be fitted to the Roo Bar, they just need to be placed on the outer side of the roo bar supports (either left or right side).

There are no problems - only solutions!

TheDocAUS · Mar 19, 2023

I see the glass half full, not half empty. Where there is a will, there is a way!

TheDocAUS · Mar 19, 2023

Some different mounting options for UHF aerials in Australia:

Oricom here.
GME here.
Uniden here.
RFI here.
Misc. here, here and here.

I have purchased an RFI bracket to test (I just need the car now

).

trobex · Mar 19, 2023

DaveB said:
I assume you are referring to these types of rod holders.
On vehicles everywhere in Australia but very much illegal.
Nothing is allowed to protrude above the bonnet line and nothing is allowed in the drivers line of sight.
Not to mention pedestrian safety rules
I guess you would have to be doing other things wrong for a cop to book you on it, or be involved in an accident.
I saw a guy get booked for driving lights on top of the bull bar (not the actual vehicle) and for his antennae's on the bar but he was driving like a dick on the Gold Coast

View attachment 7806108 View attachment 7806109 View attachment 7806110

100% illegal and you will be fined. Please also note, that any modification (bolt on tabs, brackets etc) to a certified bull bar is ALSO illegal and very dangerous tp pedestrians.

DenisM · Mar 19, 2023

TheDocAUS said:
I see the glass half full, not half empty. Where there is a will, there is a way!

Indeed.. remember: air is a fluid, thus a glass "half full", is actually full! An apparently "empty" glass is, in reality "full" !!

trobex · Mar 19, 2023

DenisM said:
Indeed.. remember: air is a fluid, thus a glass "half full", is actually full! An apparently "empty" glass is, in reality "full" !!

Haha - If you are going to break the law - do it properly!!!

DenisM · Mar 20, 2023

Shock/horror option... could always cut a hole and mount the antenna base in a suitable position on the flat surface of the front passenger-side mudguard/wing... it's out of the driver's direct line of sight, presents no hazard to pedestrians....

I have a 2.1dba magnetic base GME antenna ..it's about 150mm tall which is more than adequate for communicating with trucks +/- 3-4 Km. I place it on the roof and run the narrow coax cable between the double dust seal on the rear doors of the Santa Fe. It withstood the rigours of a Rangie P38 trip on the corrugations of the Cape York Peninsular Development Rd years ago... I'll probably use it in the same manner on the Grenadier... my larger (GME 6.2 dba) aerial however is a separate challenge...

Steveo · Mar 20, 2023

DenisM said:
Shock/horror option... could always cut a hole and mount the antenna base in a suitable position on the flat surface of the front passenger-side mudguard/wing... it's out of the driver's direct line of sight, presents no hazard to pedestrians....

I like your thinking!

Tazzieman · Mar 20, 2023

Move to Tassy; the rules about bullbars are 404 page not found.
Blind eye if you ask me

Greg · Mar 20, 2023

Would the roof tie down rails be a mounting option?

globalgregors · Mar 20, 2023

DenisM said:
Shock/horror option... could always cut a hole and mount the antenna base in a suitable position on the flat surface of the front passenger-side mudguard/wing... it's out of the driver's direct line of sight, presents no hazard to pedestrians....
I have a 2.1dba magnetic base GME antenna ..it's about 150mm tall which is more than adequate for communicating with trucks +/- 3-4 Km. I place it on the roof and run the narrow coax cable between the double dust seal on the rear doors of the Santa Fe. It withstood the rigours of a Rangie P38 trip on the corrugations of the Cape York Peninsular Development Rd years ago... I'll probably use it in the same manner on the Grenadier... my larger (GME 6.2 dba) aerial however is a separate challenge...

I had noticed that the military typically reinforce the front wing when mounting in that location, albeit they are mounting much larger whip antennae.
I wonder if there’d be any issue with a regular GME radome antenna, or would it cause deflection etc flapping around on that flat surface?

TheDocAUS · Mar 20, 2023

Greg said:
Would the roof tie down rails be a mounting option?

Yes, and Rhino Rack even has an accessory available on the INEOS website. Here is the link to Rhino Rack website of the item.

You can even mount the folding bracket along side the Rhino Rack, look here. The Razed product can be used with the GME or Rhino Rack foldable bracket.

Search

Search

Bull bar

globalgregors

Photo Contest Winner

TheDocAUS

Andrew Kilby

DaveB

Andrew Kilby

DaveB

bigleonski

TheDocAUS

Tazzieman

TheDocAUS

TheDocAUS

trobex

DenisM

trobex

DenisM

Steveo

Global Grenadier #1009

Tazzieman

Greg

globalgregors

Photo Contest Winner

TheDocAUS

Similar threads

Latest posts

Share this page