loose nut of front stabilizer

Jean Mercier · Oct 1, 2023

As I have some "noises" since I did some off-road and stone tracks some weeks ago, I regularly try to find out what's wrong.

Yesterday, as my left front wheel was in a "left turn" position, I could easily inspect the wiring and conduits. I also grabbed with my hands several parts and tried to move them, and suddenly I perceived that the stabilizer was loose, the nut became loose, see the picture. Picture was taken after giving a quarter turn to the nut, with my hand! No tools.

I tightened it, and used the paint marks to tighten it a bit more than the original position, see picture:

AnD3rew · Oct 1, 2023

Jean Mercier said:
As I have some "noises" since I did some off-road and stone tracks some weeks ago, I regularly try to find out what's wrong.

Yesterday, as my left front wheel was in a "left turn" position, I could easily inspect the wiring and conduits. I also grabbed with my hands several parts and tried to move them, and suddenly I perceived that the stabilizer was loose, the nut became loose, see the picture. Picture was taken after giving a quarter turn to the nut, with my hand! No tools.
View attachment 7828420

I tightened it, and used the paint marks to tighten it a bit more than the original position, see picture:
View attachment 7828422

Goodness me, Jean, I think INEOS just needs to take your car back and give you a new one, no one has had more issues than you. And yet you are still cheerful.

Shaky · Oct 1, 2023

That might not be an issue with just Jeans as it looks as though that nut has clearly backed off according to the green alignment marks.

Perhaps others should check theirs.

Not sure if there are torque settings for this but would be interesting to see if the green marks equate to a correct torque setting.

rovie · Oct 1, 2023

Jean Mercier said:
As I have some "noises" since I did some off-road and stone tracks some weeks ago, I regularly try to find out what's wrong.

Yesterday, as my left front wheel was in a "left turn" position, I could easily inspect the wiring and conduits. I also grabbed with my hands several parts and tried to move them, and suddenly I perceived that the stabilizer was loose, the nut became loose, see the picture. Picture was taken after giving a quarter turn to the nut, with my hand! No tools.
View attachment 7828420

I tightened it, and used the paint marks to tighten it a bit more than the original position, see picture:
View attachment 7828422

I take such advice seriously and appreciate it very much. Many thanks @Jean Mercier. I'll have a look at mine later on.

Eric · Oct 1, 2023

Jean Mercier said:
As I have some "noises" since I did some off-road and stone tracks some weeks ago, I regularly try to find out what's wrong.

Yesterday, as my left front wheel was in a "left turn" position, I could easily inspect the wiring and conduits. I also grabbed with my hands several parts and tried to move them, and suddenly I perceived that the stabilizer was loose, the nut became loose, see the picture. Picture was taken after giving a quarter turn to the nut, with my hand! No tools.
View attachment 7828420

I tightened it, and used the paint marks to tighten it a bit more than the original position, see picture:
View attachment 7828422

Has your cluck when you drive over a bump now disappeared?

Wayneos · Oct 1, 2023

Eric said:
Has your cluck when you drive over a bump now disappeared?

Yep, a loose end link would totally make that noise. A dab of blue loctite ought to keep it in place.

Jean Mercier · Oct 1, 2023

Eric said:
Has your cluck when you drive over a bump now disappeared?

No, because nothing has been done about it, and it is NOT related to that nut!
I indeed post my "problems" here, so that other people can check if they have similar problems.
The other side (right wheel) was OK in my car.

It is NOT so that I drive my car the whole time on bad roads, this is impossible in Belgium. I didn't register, but from the almost 15000 km, I probably drove less than 500 km on bad roads (mainly in Eastern Europe).

Jean Mercier · Oct 1, 2023

Wayneos said:
Yep, a loose end link would totally make that noise. A dab of blue loctite ought to keep it in place.

I did put some "red" Loctite on it, can be seen on the picture.

Wayneos · Oct 1, 2023

Jean Mercier said:
I did put some "red" Loctite on it, can be seen on the picture.

I think you need to dip your Gren IN red loctite Jean!

Jean Mercier · Oct 1, 2023

Wayneos said:
I think you need to dip your Gren IN red loctite Jean!

Why did you advise me to put blue loctite then?

Was that a political choice?

ECrider · Oct 1, 2023

Jean Mercier said:
Why did you advise me to put blue loctite then? Was that a political choice?

just don't use a 'coalition' of both. Always useless.

trobex · Oct 1, 2023

Far out... I will now also have to get my tork set out and make ready for some tightening!!! That is poor form from IA... can anyone explain what happens in that bolt disengages entirely..??

Rab · Oct 1, 2023

It’s an anti-roll bar link, so it would roll a bit more in the corners.

emax · Oct 1, 2023

Shaky said:
That might not be an issue with just Jeans as it looks as though that nut has clearly backed off according to the green alignment marks.

Not sure if there are torque settings for this but would be interesting to see if the green marks equate to a correct torque setting.

Hardly.

It is not possible to predict the position where the correct torque will be reached. So normally, the nut is tightened with the correct torque and then the mark is applied.

Lord Ripon USA · Oct 1, 2023

A common symptom of end link failure is a noticeable rattle on uneven roads. Not off road, just rough pavement.
They rattle like crazy when worn out or broken.
Very common problem on small cars in the US.

trobex · Oct 1, 2023

Rab said:
It’s an anti-roll bar link, so it would roll a bit more in the corners.

Could it roll you sideways over the mountain when you're overlanding, and it let go when you thought you were safe???

Tazzieman · Oct 1, 2023

Smart overlanders do regular checks. Sometimes daily if the roads are rough.
Also pays to have spare nuts/spring washers/loctites , torque wrench for when you forget to check.

trobex · Oct 1, 2023

Tazzieman said:
Smart overlanders do regular checks. Sometimes daily if the roads are rough.
Also pays to have spare nuts/spring washers/loctites , torque wrench for when you forget to check.

Wrench for sure - and a tig.

Jean Mercier · Oct 1, 2023

trobex said:
Wrench for sure - and a tig.

I don't want to carry a whole factory in my car

Otherwise it isn't "made in Hambach" anymore

rovie · Oct 1, 2023

rovie said:
I take such advice seriously and appreciate it very much. Many thanks @Jean Mercier. I'll have a look at mine later on.

In my case, these nuts are tight.

Search

Search

loose nut of front stabilizer

Jean Mercier

GG#920

AnD3rew

Inch deep and a mile wide.

Shaky

rovie

Eric

Wayneos

Jean Mercier

GG#920

Jean Mercier

GG#920

Wayneos

Jean Mercier

GG#920

ECrider

trobex

Rab

emax

Photo Contest Winner

Lord Ripon USA

trobex

Tazzieman

trobex

Jean Mercier

GG#920

rovie

Similar threads

Latest posts

Share this page